Ultra-Safe
Ultra-Safe Economy Cable Grab
Made in Canada.
Need it fast? We stock many items, but some rigging and safety gear has longer lead times. Contact us before placing urgent orders.
Earn rewards points.
CA Prop 65
Product Description
Ultra-Safe US-5038E Economy Cable Grab
The Ultra-Safe US-5038E is a cam-actuated fall arrester designed for smooth movement and secure fall protection along a vertical 3/8" (10mm) wire rope lifeline. It automatically follows the user during ascent or descent and locks immediately in the event of a fall. Compatible with galvanized or stainless steel wire rope, this economical cable grab meets ANSI Z359.1 and OSHA 1926.502/1910.140 standards.
Key Features
- Cam-actuated fall arrest design
- Slides freely up and down 3/8" (10mm) galvanized or stainless steel cable
- Locks instantly to arrest falls
- Connects to the chest (sternal) D-ring of harness using an ANSI/OSHA approved carabiner
- Compact and economical design with smooth trailing mobility
Compatibility & Use
- For use with 3/8" (10mm) diameter wire rope only
- Minimum cable breaking strength: 6,000 lbs (27 kN)
- Use only with ANSI/OSHA approved carabiners having a round cross-section (3/8") and total length not exceeding 9" (200mm)
- Must be used with a shock-absorbing lanyard or on a lifeline with integrated shock absorber
Installation Instructions
- Hold the cable grab with the arrow pointing upward
- Press the protruding lever upward and squeeze the housing
- Rotate the unit 90° clockwise and then 90° counterclockwise to thread the cable between the cams and body
- Release the lever to engage the cams
- Insert the carabiner into the eye at the end of the lever to lock the device in place
- Pull downward briskly to ensure the grab engages the cable properly
Inspection & Maintenance
- Inspect before each use—remove from cable and check for dirt, damage, wear, and free movement of the mechanism
- Ensure there is noticeable spring resistance and that the unit locks when released on the cable
- Clean with mild soap and water; dry with a clean cloth or low-pressure air
- Lubricate pivot area with light oil (e.g., WD-40); avoid getting oil on cams or cable contact surfaces
- Do not use if the condition of the unit is in doubt
Standards & Compliance
- ANSI Z359.1
- OSHA 1926.502 and 1910.140
Cable Requirements
- 3/8" (10mm) galvanized or stainless steel wire rope
- No kinks, frays, corrosion, grease, or dirt
- Must be tied off or weighted at the bottom
Related Items
Related Products
DBI Sala
DBI Sala Lad-Saf X2 Cable Grab
DBI Sala
DBI Sala Lad-Saf X3 Cable Grab
UltraTech
UltraTech Ultra-Containment Berm Economy Model - RPE - 6 ft x 6 ft x 1 ft
UltraTech
UltraTech Ultra-Containment Berm Economy Model - CP2000 - 10 ft x 40 ft x 1 ft
Safety Notice
Although Bishop Lifting strives to manufacture and sell the highest quality rigging and safety gear, use of the gear is dangerous if not used correctly by competent trained professionals. Bishop Lifting disclaims any liability resulting from the misuse of its rigging and safety gear. Please take a moment to more thoroughly review our disclaimer.
Bishop Lifting rigging and safety gear is only intended to be used by competent trained professionals. Misuse of the rigging and safety gear can result in serious injury up to and including loss of life. As such, Bishop Lifting disclaims liability for any misuse or incorrect product selection by our customers.
Rigging and safety gear purchased from Bishop Lifting should be used in strict accordance with all industry and OSHA standards. At no time should rigging or safety gear be used beyond its certified load ratings (aka Working Load Limits). Normal wear and tear should be expected with use of rigging and safety gear; therefore, all gear should be thoroughly inspected before each and every use. Worn or unsafe rigging and safety gear should never be used.